audio_engineering:class_b_power_calculations
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
audio_engineering:class_b_power_calculations [2022/12/13 06:35] – [Power Calculations for Class B Amplifiers] mithat | audio_engineering:class_b_power_calculations [2022/12/13 20:35] – [Power Calculations for Class B Amplifiers] mithat | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Power Calculations for Class B Amplifiers ====== | ====== Power Calculations for Class B Amplifiers ====== | ||
- | The following is derived from material presented by [[https:// | + | For the calculations below, the following are assumed: `v_o` is the amplifier output voltage, `i_o` is the output current, and `R_L` is the load resistance. It's also assumed the amplifier has a bipolar power supply with rails `V_(C C)` and `V_(E E)`, where `V_(E E) = -V_(C C)`. We further assume that transistor base currents are negligible (so collector currents equal output currents) and that the zero-conduction dead zone likewise |
- | + | ||
- | For the calculations below, the following are assumed: `v_o` is the amplifier output voltage, `i_o` is the output current, and `R_L` is the load resistance. It's also assumed the amplifier has a bipolar power supply with rails `V_(C C)` and `V_(E E)`, where `V_(E E) = -V_(C C)`. We further assume that transistor base currents are negligible (so collector currents equal output currents) and that the zero-conduction dead zone is likewise negligible. | + | |
These analyses are based on sinusoidal signals as this is the accepted standard for power and thermal design in audio. The formulae will be valid for other signals with a crest factor of `sqrt(2)`. Alternative analyses based on worst-case signals (i.e., those having a crest factor of one, e.g, square waves), may be instructive but are not presented here. | These analyses are based on sinusoidal signals as this is the accepted standard for power and thermal design in audio. The formulae will be valid for other signals with a crest factor of `sqrt(2)`. Alternative analyses based on worst-case signals (i.e., those having a crest factor of one, e.g, square waves), may be instructive but are not presented here. | ||
+ | A majority of the following is derived from material presented by [[https:// | ||
===== Power into the load ===== | ===== Power into the load ===== | ||
The average output power `bar(P_L)` into load `R_L` for a sine wave with amplitude `v_(op)` is calculated as: | The average output power `bar(P_L)` into load `R_L` for a sine wave with amplitude `v_(op)` is calculated as: | ||
Line 55: | Line 54: | ||
</ | </ | ||
- | Owing to symmetry, the negative half of the sinusoidal cycle will consume the same average power as the positive half, therefore the total average power delivered by the power supply is: | + | Owing to symmetry, the transistor connected to `V_(E E)` will consume the same average power over one cycle as the one connected to `V_(C C)`, therefore the total average power delivered by the power supply is: |
`bar(P_S) = bar(P_S)_(V+) + bar(P_S)_(V-) = bar(P_S)_(V+) + bar(P_S)_(V+) = 2 bar(P_S)_(V+)` | `bar(P_S) = bar(P_S)_(V+) + bar(P_S)_(V-) = bar(P_S)_(V+) + bar(P_S)_(V+) = 2 bar(P_S)_(V+)` | ||
Line 91: | Line 90: | ||
`P_D = bar(P_S) - bar(P_L)` | `P_D = bar(P_S) - bar(P_L)` | ||
<WRAP indent> | <WRAP indent> | ||
- | ` = (2/pi * v_(op)/R_L * V_(C C)) - [(v_(op))^2/ | + | ` = (2/pi * v_(op)/R_L * V_(C C)) - [(v_(op))^2/ |
` = ((2 V_(C C))/(pi R_L) * v_(op)) - [(v_(op))^2/ | ` = ((2 V_(C C))/(pi R_L) * v_(op)) - [(v_(op))^2/ | ||
</ | </ | ||
- | ===== Worst-case | + | ===== Maximum |
- | The plot of `P_D` vs. `v_(op)` intersects the origin when `v_(op) = 0` and describes an broad curve with a peak somewhat before its final value (when `v_(op) = V_(C C)`). To find the maxima of this curve, we solve for `(d P_d)/(d v_(op)) = 0`. Thus: | + | The plot of `P_D` vs. `v_(op)` |
`(d P_D)/(d v_(op)) = (2 V_(C C))/(pi R_L) - 2(v_(op)/ | `(d P_D)/(d v_(op)) = (2 V_(C C))/(pi R_L) - 2(v_(op)/ | ||
Line 106: | Line 105: | ||
`v_(op) = 2/pi V_(C C)` | `v_(op) = 2/pi V_(C C)` | ||
- | Substituting this into the relation for `P_D` above yields the worst-case power dissipation `P_(Dmax)`: | + | Substituting this into the relation for `P_D` above yields the maximum (i.e., |
`P_(Dmax) = ((2 V_(C C))/(pi R_L) * 2/pi V_(C C)) - [(2/pi V_(C C))^2/ | `P_(Dmax) = ((2 V_(C C))/(pi R_L) * 2/pi V_(C C)) - [(2/pi V_(C C))^2/ | ||
Line 125: | Line 124: | ||
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
- | < | + | < |
`P_(Dmax) = 2/pi^2 * (V_(C C))^2/ | `P_(Dmax) = 2/pi^2 * (V_(C C))^2/ |
audio_engineering/class_b_power_calculations.txt · Last modified: 2024/06/26 20:30 by mithat