I have done quite a bit of consulting work for Audio by Van Alstine over the years. I'm summarizing below some of it. While I completed a number of smaller projects for AVA before 2002, I decided to pick up the story with the Transcendence Five as that is the first product that was my complete circuit design. The list below isn’t exhaustive.

The focus of my work with AVA has always been to bring the highest standards of audio engineering to the company while helping to foster a more considered and inclusive view of the industry and its consumers.

c. 2002

New vacuum tube line stage to replace AVA’s existing design originally derived from the Dyna PAS 3.

Contribution: Concept origination, development, and implementation. I’m pretty sure this was the first commercial application of my vacuum tube computer optimization methods based on my SPICE model optimization work.

Discussion: I thought the time had come for AVA to have a new vacuum tube line-level stage to replace their aging 12AX7A-based design, and they agreed. I based the initial work around two stages of 12AT7A gain using heaps of SPICE modeling to optimize the circuit behavior for audio reproduction. I originally wanted to apply the design optimization methods to a number of different tube triodes and subjectively evaluate the results. But after hearing the results with the 12AT7A, AVA decided to put the design into production immediately. A variant of this stage remains in production today in the form of AVA’s Fet Valve CFR and FetValve CF RB preamps.

c. 2002

Low-cost hybrid line stage using a computer-optimized 12AT7A gain stage and IC buffer output stage.

Contribution: Concept origination, development, and implementation.

Discussion: This was a continuation of the work I started with the Transcendence Five. Historically, AVA had demonstrated some success with two different hybrid approaches. In the first, high-voltage MOSFET buffers were placed inside the main feedback loop of vacuum tube gain stages. In the second, a low-cost opamp stage was used to provide high impedance buffering of a conventional closed-loop tube preamp design. My idea centered around placing a high-speed solid-state buffer IC stage inside the global feedback loop. This would allow AVA to offer a preamp with performance that exceeded their tube/MOSFET hybrid at a considerable cost savings. AVA considered the design so good that it obsoleted their tube/MOSFET hybrid preamp until I was able to complete work on the Transcendence Seven.

c. 2002

12AT7A-based premium hybrid line stage using a computer-optimized 12AT7A gain stage and optimized power-MOSFET buffer output stage.

Contribution: Development and implementation. This was a major rethink of the work covered by AVA's “Fet Valve” patent and embodied in their first-generation Fet Valve products.

Discussion: One of the reasons my Transcendence Six design outperformed AVA’s more costly discrete MOSFET hybrid approach was that it used the optimized 12AT7A-based gain stage core initially developed for the Transcendence Five. So a natural progression was to see whether using that gain stage in one of their patented discrete MOSFET output buffer architectures provided an advantage over the IC-based buffer I designed into the Transcendence Six. In the process of designing the new MOSFET stage, I revisited a number of assumptions AVA made in the original implementation and produced an optimized circuit that was significantly simpler than the one it replaced. AVA thought its performance warranted it being offering as a premium hybrid product.

c. 2002

All-tube buffered line stage using a computer-optimized 12AT7A gain stage and 12AU7 buffer stage.

Contribution: Concept origination and development.

Discussion: While working on the Transcendence Seven, I was able to take a deep dive into the tube/MOSFET architecture covered in the AVA Fet Valve patent. One result of this is that I could not find a convincing reason why a power-MOSFET was better suited to buffering the gain stages over a cathode follower, but I was able to come up some reasons a MOSFET might be worse. So I developed an iteration of the Transcendence Seven design using a 12AU7A-based circuit to replace the power-MOSFET stage.

At the time I wasn’t given the go-ahead to prototype and test this design. My understanding is that AVA wanted to maintain a commitment to their patented hybrid architecture as they felt this gave them marketing distinction. However, this circuit was eventually put into production around 2014 as the Fet Valve CF.

c. 2004

All-new power high-voltage supply regulation circuits for use with all AVA tube and hybrid products.

Contribution: Concept origination, development, and implementation.

Discussion: To address a concern AVA raised regarding the audibility of B+ power supply shifts caused by line voltage variations and other factors, I developed an active regulation architecture using voltage references and high-voltage power-MOSFETs. The approach was simple and cost-effective enough that several independent regulation stages could be used to better isolate the individual stages that comprised an entire design. AVA felt that the subjective improvements resulting from the regulated power supplies warranted the adoption of the scheme in all tube and hybrid products. This resulted in the Transcendence Five SLR, Transcendence Six SLR, and Transcendence Seven SLR and ECR. The same work was also applied to the Fet Valve EXR power amplifiers.

The Ultra preamplifier (c. 2006) was essentially a Transcendence Seven SLR with a greater number of regulation stages. Similarly, the first version of the Transcendence Eight (c. 2006) was essentially a Transcendence Five SLR with more regulators. I wasn’t involved in the development of these particular applications of this regulator design as my ongoing work for AVA went on hiatus just before these products went into development.

c. 2004

Remote controlled volume circuit adaptable to all existing AVA preamplifiers.

Contribution: Concept origination, development, and implementation.

Discussion: I was aware that AVA was losing preamplifier sales because they didn’t support any kind of remote control and that AVA, given their manufacturing quantities and methods, regarded even the simplest of remote control functionality an unsolvable problem. So I decided to solve it. The solution hinged on sourcing a motorized potentiometer that was as good as the potentiometers they were using and on working with a turnkey supplier of remote control transmitters and pre-programmed receiver ICs. The result involved minimal changes to the chassis design and a build that was easier than the non-remote approach they had been using.

My expectation was that AVA would offer the remote as standard equipment on all “big body” preamplifiers. Instead it was offered as a relatively costly option, which they justified because the remote control transmitters were costly, which they were because of the small quantities they ordered them in, which was the case because remote control was offered only as an option.

c. 2005

Revision of AVA’s low-power tube amplifier circuits for the Dyna ST70 chassis.

Contribution: Strategization and development. Changes centered on improving loop behavior and power supply regulation, producing a circuit design that has remained in the AVA catalog for over 13 years.

Discussion: AVA felt they needed to produce a revision of their Dyna 70 rebuild offering and asked me to design it. I was proscribed from changing the tube complement or making similar large changes. So I opted to apply to the existing circuit some of the insights we gained from the applying regulated power supplies in tube and hybrid applications and to revisit the assumptions about pole and zero locations that the original Dyna engineers had made, likely based on the kinds of parts that were available in 1959 and definitely based on the slightly different tube complement. The revisions resulted in the Ultimate 70, and the circuit continues today in different packaging as the AVA Ultravalve amplifier.

c. 2009

Next-generation S/PDIF decoder and DAC board

Contribution: Design and implementation.

Discussion: In the mid-1990s, I built AVA a prototype stand-alone DAC that demonstrated to them that producing such a product was within their abilities—something they had previously considered impossible. So it was probably natural that years later they approached me to design the core circuits that would be used in their next-generation of stand-alone DACs. They had preselected the the Wolfson WM8740 as the DAC IC they wanted the design based around, but by the time the design was completed we had moved to the WM8742.

AVA originally wanted to support only 44.1kHz PCM formats with a single coaxial S/PDIF input. Additionally, their manufacturing capabilities precluded the use of microcontrollers. In spite of these constraints, I designed in automatic support for up to 96kHz PCM streams, jumper-configurable support for 192kHz PCM, and support for multiple inputs. Because of this, AVA was able to use this same design to meet subsequent customer demands for high-rate audio support and multiple inputs. This board was used unchanged for all AVA DAC production for seven years until it was replaced by my DAC MK5 design.

This would be the first time AVA would use predominantly SMD parts in a PCB design. The previous generation DAC had used a single hand-soldered SMD package. This design used SMD components exclusively.

I was not involved in the development of the analog stages for the first DAC products using this board. However, I was responsible for the analog circuits found in the 2015 revision.

c. 2014

All-tube, next-generation premium preamp line stage.

Contribution: Concept origination and development.

Discussion: Around 2014, finding that hybrid topologies were becoming a marketing liability rather than as asset, AVA revisited my “T7 CF” design work without my knowledge. To my original circuit design of 2002, they added grid stopper resistors ahead of the 12AU7A stages (which my original simulations didn’t point to the need for). They released it as the Fet Valve CF, and it remains in production today as the Fet Valve CFR and Fet Valve CF RB.

c. 2014

Component value selection for best RIAA conformance.

Contribution: Development.

Discussion: AVA decided to pursue a stronger presence in the growing phono market by developing a stand-alone phono preamp. I was consulted on the project near the end of its development to determine the best passive component values to yield the best RIAA conformance. I provided some subjective evaluations of the unit while it was being developed as well. I had nothing to do with the preamp’s topology or other design decisions.

c. 2015

New reconstruction and output stage based on a discrete, class-A, solid-state gain stage I developed as an independent project.

Contribution: Concept origination, development, and implementation.

Discussion: I had been developing a discrete, class-A, solid-state gain stage as an independent project for a number of years. My goal was to create a design that was free of the issues I kept hearing in opamp ICs. Late in 2014 I thought I succeeded, and so I built a single-stage differential-to-single-ended anti-imaging filter/output stage using the module for the Vision DAC board I had designed earlier for AVA. The result impressed AVA enough that it was immediately adopted for their Vision DAC offerings.

c. 2015

New line stage based on a discrete, class-A, solid-state gain stage (developed as an independent project).

Contribution: Development and implementation.

Discussion: Based on the performance gains my discrete gain-cell module provided the Vision DAC, AVA became interested in using it for their solid-state preamp offering.

c. 2017 or this

All-new DAC product with USB and S/PDIF inputs supporting high-rate PCM and DSD formats.

Contribution: Development and implementation. All-new DAC implementation based on the AK4490EQ. All-new reconstruction filter and output stage circuitry based on my discrete, class-A, solid-state gain stage. Fully isolated S/PDIF receiver based on the AK4118EQ. Galvanic isolation and switching for the Amanero Combo384 USB receiver. Microcontroller programming for input decoding, DAC operation, and user interface. Industrial design subject to AVA’s production and styling constraints. Production workflow refinements to accommodate large-scale SMD production.

Discussion: With the Vision DAC incapable of effectively supporting newer in-demand digital audio formats, AVA asked me to design for them a product that would. The original design brief specified support for up to 192kHz PCM sample rates and DSD64. I insisted on a design that provided support for DSD128 as well and that had the infrastructure to support DSD256 once that format matured. Full support for DSD256 was added in 2018.

Working with application engineers at AKM, I developed support circuitry for the AK4490EQ whose low-frequency reference voltage stability was significantly greater than the circuits used in AK4490EQ reference designs. This in turn reduced the low frequency nonlinearity of the DAC appreciably over more conventional approaches.

This would be the first design that required AVA to use microcontrollers they would burn in-house, and it did so in a big way. I ended up using three independent microcontrollers in the final product, one for each of the DAC’s core functions: input selection and control, DAC control, and the user interface. Also notable in this design is the scale to which SMD technology was adopted and the high level of build integration. These required introducing significant changes to AVA’s manufacturing workflow, which in turn brought AVA’s production methods more in line with modern approaches.

c. 2017 or this

Fully remote-controllable chassis and supporting circuitry.

Contribution: Concept origination, development, and implementation. Minimal-path relay-controlled input selection, custom user interface design and microcontroller programming, and improved manufacturability over the previous generation's less capable chassis. Industrial design, subject to AVA’s existing production and styling constraints.

Discussion: I had two main goals with this project. The first was to bring the remote controllability of AVA preamplifiers up to feature parity with the competition as quickly as possible, and the second was to move AVA away from the costly turnkey remote control solution I adopted for their initial remote control offering. An additional goal was to simplify the assembly of preamplifiers. I originally planned to work on the first of these goals immediately after completing the volume-only remote control design back in 2004. I had even gotten as far as producing prototype PCBs and a prototype build using relay-controlled input switching. But AVA opted for different priorities at the time, and this work was tabled. In 2017, the case for developing a fully remote-controllable platform was far more undeniable.

c. 2018

Low-cost remote controlled volume circuit adaptable to AVA's existing RB chassis.

Contribution: Concept origination, development, and implementation.

Discussion: Given the availability of a less costly remote control transmitter that I secured for the SLR and CFR chassis and AVA's new ability to burn microcontrollers in-house, it was natural to apply these to replace the more expensive and now 14 year old design still being used in their RB (Real Basic) preamplifer chassis. As was the case 14 years before, I expected AVA to adopt the remote control as standard equipment on the RB chassis, but again they decided to offer it as an option, albeit not as costly as the solution it replaced. As of early 2021, they have made it a standard feature for all preamps using this chassis design.

c. 2020–2021

Embedded design for IR remote control sending with silicone membrane switches.

Contribution: Concept origination, development, and implementation.

Discussion: To help address issues with supplier chains in AVA's existing remote control vendors, I decided it would be a good idea if they had the ability to vertically integrate remote control production as needed. This is the first fruit of that endeavor. It is a PCB based around a very low power microcontroller implementation and accompanying firmware that is retrofitted into one of AVA's existing vendor-supplied cases. The solution provides in-house customization of remote control codes and their timing.

c. 2018–2021

Contribution: Concept origination, development, and implementation.

Discussion: The DVA Digital Preamplifier is effectively an expansion of the DAC MK5. It reworks that product's output stage to provide a differential output as well as some gain while also implementing control of volume and input selection via a touchscreen and remote control. Thus, it eliminates the need for an analog preamp. This is, of course, how many users with primarily digital sources have been doing things for a long time now. It just took a bit of time to convince AVA of the advantages of this. Now that it's done, they are all-in. That said, getting to done was no easy feat. Development was beset by seemingly myriad hurdles, ranging from the fire at the AKM factory to the prolonged COVID-19 Great Parts Apocalypse.

The DVA Digital Preamplifier also brought forth a new design aesthetic and chassis mechanics that I originally intended as a one-off transitional one. As is often the case, it took a good amount of work to convince AVA of the merits of making the change. But once the design was released, it received, for the first time ever for an AVA product, praise in the audiophile press for its aesthetics. Likely as a result of this, AVA asked me to design or redesign faceplates for a variety of new and existing products.

What this means is that my original plan of transitioning to a completely new design program that takes updated user, business, and manufacturing requirements into full consideration will be delayed. I regard this as an odd manifestation of Raymond Loewy's MAYA principle.

c. 2021

Contribution: Concept origination, development, and implementation.

Discussion: Coming soon.

c. 2021

Contribution: Concept origination, development, and implementation.

Discussion: Coming soon.

I continue to provide consulting services to Audio by Van Alstine, particularly in the areas of digital audio, small-signal analog audio, circuit simulation, and user interface design. For reasons that should be obvious, I'm not at liberty to discuss projects under development.

Within audio, my work focuses on developing solutions that represent meaningful audio progress rather than chasing colorations that happen to be the current fashion. At a more general level, my design interests include a bringing greater equity to all technological realms and improving user experiences in every stage of product use. I try to bring this to bear as much as possible in my work for AVA.