arduino:stm32_blue_pill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arduino:stm32_blue_pill [2019/10/02 13:00] – [Resources] mithat | arduino:stm32_blue_pill [2020/06/22 20:09] – mithat | ||
---|---|---|---|
Line 5: | Line 5: | ||
===== Setup ===== | ===== Setup ===== | ||
- | ==== Arduino environment | + | ==== Hardware |
- | Do once: | + | In addition to a "Blue Pill," you will need a **3.3V USB to serial converter**. I used a [[https:// |
- | * Under // | + | <WRAP center round important 90%> |
- | * Under //Tools > Board > Boards Manager ...//, find "**STM32F1xxx/ | + | **Be careful!** |
- | ==== Hardware ==== | + | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Applying 5V to the 3.3V main supply line of a Blue Pill will kill it. |
- | In addition | + | Lots of pins on the STM32F103C8T6 are purported |
- | <WRAP center important 90%> | + | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. |
- | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Be careful! | + | </ |
- | Applying 5V to the 3.3V main supply line of Blue Pill will kill it. | + | * Connect ground from the serial converter board to the '' |
+ | * Connect the serial converter' | ||
+ | * Connect the serial converter' | ||
+ | * If you will be powering the Blue Pill from the serial converter board, connect VCC from the serial converter board to the '' | ||
- | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. | + | ==== Arduino environment ==== |
- | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't! I don't know if TX/RX are. | + | Do once: |
- | </ | + | |
- | * Connect VCC and ground from the serial converter board to the '' | + | * Under //Files > Preferences//, |
- | * Connect the serial converter' | + | * Under //Tools > Board > Boards Manager ...//, find " |
==== Project config ==== | ==== Project config ==== | ||
Line 49: | Line 51: | ||
===== Pinout ===== | ===== Pinout ===== | ||
- | From [[https:// | + | From [[https:// |
{{: | {{: | ||
===== Resources ===== | ===== Resources ===== | ||
- | Note that the stm32duino.com domain has [[https:// | + | |
+ | ==== STM32duino ==== | ||
+ | Note that the stm32duino.com domain has [[https:// | ||
* [[http:// | * [[http:// | ||
- | | + | |
- | * [[https:// | + | * [[https:// |
* [[https:// | * [[https:// | ||
- | * Pinout: [[https:// | ||
* [[https:// | * [[https:// | ||
+ | |||
+ | ==== Other ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ |
arduino/stm32_blue_pill.txt · Last modified: 2022/06/26 01:18 by mithat