arduino:stm32_blue_pill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arduino:stm32_blue_pill [2019/09/15 00:49] – [Pinout] mithat | arduino:stm32_blue_pill [2019/11/05 21:55] – mithat | ||
---|---|---|---|
Line 4: | Line 4: | ||
===== Setup ===== | ===== Setup ===== | ||
- | |||
- | ==== Arduino environment ==== | ||
- | |||
- | Do once: | ||
- | |||
- | * Under //Files > Preferences//, | ||
- | * Under //Tools > Board > Boards Manager ...//, find " | ||
==== Hardware ==== | ==== Hardware ==== | ||
- | In addition to your "Blue Pill," you will also need a **3.3V USB to serial converter**. I used a [[https:// | + | In addition to a "Blue Pill," you will need a **3.3V USB to serial converter**. I used a [[https:// |
<WRAP center important 90%> | <WRAP center important 90%> | ||
- | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Be careful! | + | Be careful! |
- | Applying 5V to the 3.3V main supply line of Blue Pill will kill it. | + | Lots of pins on the STM32F103C8T6 are purported |
There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. | ||
- | |||
- | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't! I don't know if TX/RX are. | ||
</ | </ | ||
- | * Connect | + | * Connect ground from the serial converter board to the '' |
- | * Connect the serial converter' | + | * Connect the serial converter's RX to the Blue Pill's '' |
+ | * Connect the serial converter' | ||
+ | * If you will be powering the Blue Pill from the serial converter board, connect VCC from the serial converter board to the '' | ||
+ | |||
+ | ==== Arduino environment ==== | ||
+ | |||
+ | Do once: | ||
+ | |||
+ | * Under //Files > Preferences//, | ||
+ | * Under //Tools > Board > Boards Manager ...//, find " | ||
==== Project config ==== | ==== Project config ==== | ||
Line 49: | Line 49: | ||
===== Pinout ===== | ===== Pinout ===== | ||
- | From [[https:// | + | From [[https:// |
{{: | {{: | ||
===== Resources ===== | ===== Resources ===== | ||
- | Note that the stm32duino.com domain has gone down at least once because it exceeded the host's traffic limit. | + | |
- | * [[https:// | + | ==== STM32duino ==== |
- | * [[https://www.stm32duino.com/ | + | Note that the stm32duino.com domain has [[https:// |
- | * Pinout: | + | |
+ | | ||
+ | | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | ==== Other ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// |
arduino/stm32_blue_pill.txt · Last modified: 2022/06/26 01:18 by mithat