arduino:stm32_blue_pill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arduino:stm32_blue_pill [2019/09/15 00:48] – [Pinout] mithat | arduino:stm32_blue_pill [2020/09/26 19:44] – [STM32 "Blue Pill"] mithat | ||
---|---|---|---|
Line 3: | Line 3: | ||
Some quick notes about setting up a STM32F103C8T6 [[https:// | Some quick notes about setting up a STM32F103C8T6 [[https:// | ||
- | ===== Setup ===== | + | <WRAP center round info 60%> |
+ | This describes the process for settings things up using the now unsupported [[https:// | ||
- | ==== Arduino environment ==== | + | The main alternative that is supported is the [[https:// |
+ | </ | ||
- | Do once: | + | ===== Setup ===== |
- | + | ||
- | * Under //Files > Preferences//, | + | |
- | * Under //Tools > Board > Boards Manager ...//, find " | + | |
==== Hardware ==== | ==== Hardware ==== | ||
- | In addition to your "Blue Pill," you will also need a **3.3V USB to serial converter**. I used a [[https:// | + | In addition to a "Blue Pill," you will need a **3.3V USB to serial converter**. I used a [[https:// |
- | <WRAP center important 90%> | + | <WRAP center |
- | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Be careful! | + | **Be careful!** |
- | Applying 5V to the 3.3V main supply line of Blue Pill will kill it. | + | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Applying 5V to the 3.3V main supply line of a Blue Pill will kill it. |
- | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. | + | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't. I don't know if TX/RX are. |
- | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't! I don't know if TX/RX are. | + | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. |
</ | </ | ||
- | * Connect | + | * Connect ground from the serial converter board to the '' |
- | * Connect the serial converter' | + | * Connect the serial converter's RX to the Blue Pill's '' |
+ | * Connect the serial converter' | ||
+ | * If you will be powering the Blue Pill from the serial converter board, connect VCC from the serial converter board to the '' | ||
+ | |||
+ | ==== Arduino environment ==== | ||
+ | |||
+ | Do once: | ||
+ | |||
+ | * Under //Files > Preferences//, | ||
+ | * Under //Tools > Board > Boards Manager ...//, find " | ||
==== Project config ==== | ==== Project config ==== | ||
Line 49: | Line 57: | ||
===== Pinout ===== | ===== Pinout ===== | ||
- | From [[https:// | + | From [[https:// |
- | {{: | + | {{: |
===== Resources ===== | ===== Resources ===== | ||
- | Note that the stm32duino.com domain | + | |
- | * [[https:// | + | ==== STM32duino ==== |
- | * [[https://www.stm32duino.com/ | + | The [[https:// |
- | * Pinout: | + | |
+ | | ||
+ | | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | |||
+ | |||
+ | ==== Other ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// |
arduino/stm32_blue_pill.txt · Last modified: 2022/06/26 01:18 by mithat