arduino:stm32_blue_pill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arduino:stm32_blue_pill [2018/10/26 22:19] – mithat | arduino:stm32_blue_pill [2020/09/20 20:29] – [STM32 "Blue Pill"] mithat | ||
---|---|---|---|
Line 3: | Line 3: | ||
Some quick notes about setting up a STM32F103C8T6 [[https:// | Some quick notes about setting up a STM32F103C8T6 [[https:// | ||
- | ===== Setup ===== | + | <WRAP center round info 60%> |
+ | This describes the process for settings things up using the now unsupported and OBSOLETE [[https:// | ||
- | ==== Arduino environment ==== | + | An alternative that is currently supported is the [[https:// |
+ | </ | ||
- | Do once: | + | ===== Setup ===== |
- | + | ||
- | * Under //Files > Preferences//, | + | |
- | * Under //Tools > Board > Boards Manager ...//, find " | + | |
==== Hardware ==== | ==== Hardware ==== | ||
- | You'll need a "Blue Pill." | + | In addition to a "Blue Pill," |
- | <WRAP center important 90%> | + | <WRAP center |
- | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't! I don't know if TX/RX are. | + | **Be careful!** |
- | There is a 5V input on the board and a USB connector that can power the board. These are purported to go through a small 3.3V regulator. | + | Some serial converter boards put out 5V as VCC even when set to 3.3V mode. Applying 5V to the 3.3V main supply line of a Blue Pill will kill it. |
+ | |||
+ | Lots of pins on the STM32F103C8T6 are purported to be 5V tolerant, but the main DC isn't. I don't know if TX/RX are. | ||
+ | |||
+ | There is a 5V input on the Blue Pill and a USB connector that can power the board from 5V. These go through a small 3.3V regulator. | ||
</ | </ | ||
- | * Connect | + | * Connect ground from the serial converter board to the '' |
- | * Connect the serial converter' | + | * Connect the serial converter' |
+ | * Connect the serial converter' | ||
+ | * If you will be powering the Blue Pill from the serial converter board, connect VCC from the serial converter board to the '' | ||
+ | |||
+ | ==== Arduino environment ==== | ||
+ | |||
+ | Do once: | ||
+ | |||
+ | * Under //Files > Preferences//, | ||
+ | * Under //Tools > Board > Boards Manager ...//, find " | ||
==== Project config ==== | ==== Project config ==== | ||
Line 29: | Line 41: | ||
* //Board// : " | * //Board// : " | ||
- | * //Variant// : " | + | * //Variant// : " |
* //Upload method// : " | * //Upload method// : " | ||
+ | * //CPU Speed(MHz)// | ||
* // | * // | ||
* //Port// : wherever the serial converter is plugged into | * //Port// : wherever the serial converter is plugged into | ||
Line 36: | Line 49: | ||
===== Programming ===== | ===== Programming ===== | ||
- | * Move the top jumper to the 1 (right) position. | + | * Move the top jumper |
* Push reset. | * Push reset. | ||
* Upload the sketch. | * Upload the sketch. | ||
Line 43: | Line 56: | ||
To put the device into " | To put the device into " | ||
- | ===== Resources | + | ===== Pinout |
- | | + | From [[https:// |
- | * [[https:// | + | {{: |
+ | |||
+ | |||
+ | ===== Resources ===== | ||
+ | |||
+ | ==== STM32duino ==== | ||
+ | Note that the stm32duino.com domain has [[https:// | ||
+ | |||
+ | * [[http:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | ==== Other ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// |
arduino/stm32_blue_pill.txt · Last modified: 2022/06/26 01:18 by mithat