Differences

This shows you the differences between two versions of the page.

--- arduino:arduino_crash_course:misc [2015/02/16 03:14] – [Binary output] mithat
+++ arduino:arduino_crash_course:misc [2015/02/16 04:22] (current) – [Serial communication] mithat
@@ Line 18: / Line 18: @@
   * **AREF.** Reference voltage for the analog inputs. Used with analogReference().
   * **Reset.** Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board." ((http://arduino.cc/en/Main/ArduinoBoardUno))
+==== "Most preferred" pins ====
+Special functions are consumed by:
+  * **I2C (TWI):** A4 and A5.
+  * **SPI:** 10, 11, 12, 13.
+  * **Interrupts:** 2, 3.
+  * **Serial:** 0, 1
+This leaves:
+  * **Digital out/in:** 4, 7, 8
+  * **PWM out:** 9, 10, and 11; pins 5 and 6 have higher-than-expected duty cycles.
+  * **Analog or digital out/in:** A0, A1, A2, A3
+Note that pin 13 also has a pullup resistor on it for the internal LED, meaning it's a poor choice for use as an input even if you're not using SPI.
 ----
-===== I/O config =====
+===== I/O =====
-  * "The analog input pins can be used as digital pins, referred to as A0, A1, etc." ((http://arduino.cc/en/Reference/PinMode))
+==== Output ====
-==== Binary output ====
+=== Digital output ===
   * Output is limited to 40mA. More current draw can destroy the chip.
   * There are no output resistors.
@@ Line 31: / Line 48: @@
 <code c>
-const int LED = 13;
+const int LED_PIN = 13;
 setup() {
-  pinMode(LED, OUTPUT);
+  pinMode(LED_PIN, OUTPUT);
 }
 loop() {
-  digitalWrite(LED, HIGH);
+  digitalWrite(LED_PIN, HIGH);
-  digitalWrite(LED, LOW);
+  digitalWrite(LED_PIN, LOW);
 }
 </code>
-==== PWM output ====
+  * "The analog input pins can be used as digital pins, referred to as A0, A1, etc." ((http://arduino.cc/en/Reference/PinMode))
+  * "The analog pins can be used identically to the digital pins, using the aliases A0 (for analog input 0), A1, etc.  For example, the code would look like this to set analog pin 0 to an output, and to set it HIGH: " ((http://arduino.cc/en/Tutorial/AnalogInputPins))
+<code c>
+pinMode(A0, OUTPUT);
+digitalWrite(A0, HIGH);
+</code>
+=== PWM output ===
   * PWM around 490 or 980 Hz.
   * "You do not need to call pinMode() to set the pin as an output before calling analogWrite()." ((http://arduino.cc/en/Reference/AnalogWrite))
@@ Line 49: / Line 74: @@
 <code c>
-const int LED = 11; /* 3,5,6,9,10,11 on Uno. */
+const int LED_PIN = 11;      /* 3,5,6,9,10,11 on Uno. */
 loop() {
-  analogWrite(LED, /*0 to 255*/);
+  analogWrite(LED_PIN, 127); /* 0 to 255. */
 }
 </code>
-==== Binary input ====
+==== Input ====
-  * "Arduino (Atmega) pins default to inputs. Approx load in 100M ohm." ((http://arduino.cc/en/Tutorial/DigitalPins))
+=== Digital input ===
+  * "Arduino (Atmega) pins default to inputs. Approx load is 100M ohm." ((http://arduino.cc/en/Tutorial/DigitalPins))
   * Internal pullup resistors are disabled by default.
@@ Line 71: / Line 98: @@
   btnState = digitalRead(BUTTON);
 }
+</code>
+  * "The analog input pins can be used as digital pins, referred to as A0, A1, etc." ((http://arduino.cc/en/Reference/PinMode))
+  * "The analog pins can be used identically to the digital pins, using the aliases A0 (for analog input 0), A1, etc." ((http://arduino.cc/en/Tutorial/AnalogInputPins))
+<code c>
+pinMode(A0, INPUT);
+btnState = digitalRead(A0);
 </code>
@@ Line 84: / Line 119: @@
 </code>
-==== A/D input ====
+=== A/D input ===
+  * 10-bit unsigned A/D conversion with about 10kHz sample rate.
+  * Default reference to 5VDC. Can be overridden via ''analogReference();''.
+  * No setup is needed.
 <code c>
+int ANALOG_PIN = 3;  // Maps to A3 we think.
+int val = 0;
+void loop() {
+  val = analogRead(ANALOG_PIN);    // read the input pin
+}
 </code>
+----
+===== Serial communication =====
+  * Serial I/O consumes pins 0 (for RX) and 1 (for TX) if used.
+  * [[http://arduino.cc/en/Reference/Serial|Serial reference]]
+==== Serial output ====
+Simple reporting:
+<code c>
+void setup() {
+  Serial.begin(9600);  // init serial communication at 9600 bps
+}
+void loop() {
+  Serial.write(65);           // write a byte (interpreted as ASCII)
+  Serial.print(42);           // print a number
+  Serial.println("Yo.");      // print a string as a line
+  Serial.print(78, HEX);      // print "4E"
+  Serial.println(1.23456, 4); // print "1.2346"
+  Serial.end();               // release pins 0 and 1 for general use
+}
+</code>
+==== Serial output ====
+Later.
+----