Differences

This shows you the differences between two versions of the page.

--- arduino:arduino_crash_course:analog_input [2012/11/06 01:12] – [Night light] mithat
+++ arduino:arduino_crash_course:analog_input [2017/12/06 01:27] (current) – [Night light] mithat
@@ Line 1: / Line 1: @@
 ====== Analog Input ======
-As we have seen, an Arduino digital input is one that have one of two states: HIGH or LOW. Most Arduino implementations also permit you to connect an input whose value can be any value between 0 volts and (by default) the power-supply voltage and then convert the input level to an internal digital value between 0 an 1204. The Arduino literature refers to these as "analog" inputs. The process of converting a real analog signal to a digital number is called **analog to digital conversion** (**ADC**).
+As we have seen, an Arduino digital input is one that have one of two states: HIGH or LOW. Most Arduino implementations also permit you to connect an input whose value can be any value between 0 volts and (by default) the power-supply voltage, and then convert the input level to an integer value between 0 an 1023. The Arduino literature refers to these as "analog" inputs. The process of converting a physical analog signal to a digital representation is called **analog to digital conversion** (**ADC**).
-Consult the documentation for your specific Arduino board to detmine which pins support analog input.
+Consult the documentation for your specific Arduino board to determine which pins support analog input. On the Arduino UNO, inputs A0 through A5 can be used as analog inputs.
 ===== Night light =====
@@ Line 10: / Line 10: @@
 <WRAP center round tip 60%>
-CdS cells are notoriously tweaky devices. A lot of experimentation with your particular cell will probably be required to see what your circuit is actually doing--quite likely requiring the use of the serial communication to report the ADC values.
+CdS cells are notoriously tweaky devices. A lot of experimentation with your particular cell will probably be required to see what your circuit is actually doing---quite likely requiring the use of the serial communication to report the ADC values (see [[light_meter|this]] for an example).
-There are more reliable and calibrated light-level sensors available that may be a better (but significanly more expensive!) choice if you wish not to deal with the tweakiness of Cds cells.
+There are more reliable and calibrated light-level sensors available that may be a better (but significantly more expensive!) choice if you wish not to deal with the tweakiness of Cds cells.
 </WRAP>
+FIXME We need a circuit diagram
-TODO:
+In the following example, we output the light-level reading to serial communication. This should help you get a feel for the range of numbers that result from for your particular unit.
-  - <del>determine default analog Vref</del>
-  - hook up CdS and find a resistor that gets decent range
+<file c cds2serial.ino>
-  - program!
+/*
+ CdS to Serial
+ Ouptut the reading on the CdS pin to Serial.
+ */
+const int inputPin = A0;         // use analog 0 (A0) as input pin
+const int ledPin = 13;           // connect the LED to pin 13
+int lightLevel = 0;              // used to store the input value
+void setup() {
+  Serial.begin(9600);            // initialize serial communication
+  pinMode(ledPin, OUTPUT);       // make LED's pin an output
+}
+void loop() {
+  lightLevel = analogRead(inputPin);  // get an analog reading
+  Serial.println(lightLevel);         // print out the reading
+  delay(500);                         // delay between reads
+}
+</file>
+And here is the working nightlight. You may have to adjust ''lightThreshold'' so it works well with your particular CdS cell.
+<file c NightLight.ino>
+/*
+ NightLight
+ Turn an LED on when the ambient light is below a certain value.
+ */
+const int lightThreshold = 800;  // value below which LED turns on
+const int inputPin = A0;         // use analog 0 (A0) as input pin
+const int ledPin = 13;           // connect the LED to pin 13
+int lightLevel = 0;              // used to store the input value
+void setup() {
+  pinMode(ledPin, OUTPUT);       // make LED's pin an output
+}
+void loop() {
+  lightLevel = analogRead(inputPin);  // get an analog reading
+  if (lightLevel <= lightThreshold)
+    digitalWrite(ledPin, HIGH);       // turn the LED on
+  else
+    digitalWrite(ledPin, LOW);        // turn the LED off
+}
+</file>